To attempt to fix the cracked or broken plastic knob yourself, you can use epoxy glue. Apply the epoxy to the cracked area of the knob and hold it together while drying with a pair of needle nose pliers. Hold the plastic together for the amount of time the epoxy instructions advise you.
– Shut off the power. Unplug the dryer. …
– Pull the knob off. Pull the control knob straight up and off of the front of the push-to-start switch. …
– Remove the back panel. …
– Remove the push-to-start switch. …
– Install the new push-to-start switch. …
– Reattach the back panel. …
– Reinstall the control knob. …
– Restore power to the dryer.
Thereof, Can you bypass the start switch on a dryer?
It’s a momentary contact switch for starting the motor. If you bypass it, the dryer will start as soon as the timer is turned on.
Also to know is, How do I know if my dryer starter switch is bad? When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
Subsequently, question is, How do I know if my dryer timer is bad? Clip or touch one probe to the terminal from which you removed the wire. Touch the other probe to one of the other terminals. You should get a reading of zero. If you get a high reading, then the timer motor is bad and it’s time to replace it.
Also, When I press the start button on my dryer nothing happens?
A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor so a broken motor relay can prevent the dryer from starting. … In electric dryers, a blown thermal fuse can keep the dryer from starting.
How do I fix the Start button on my Whirlpool dryer?
How much does it cost to fix a dryer timer?
Item Unit Cost Total Cost
—————————– ——— ———-
Replacement of the dryer belt $130 each $230
Replacing the heating element $180 each $280
Timer replacement $125 each $225
How do you bypass the Start button on a dryer?
How do you replace a dryer timer knob?
What would cause my dryer not to start?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … Check your power cord and the house circuit breaker. Try resetting the breaker to make sure it’s not tripped.
How do you test a timer on a electric dryer?
Test the Timer Set the dial on the multimeter to read “0”. Touch one probe to the terminal where you removed the wire and the second probe to any other contact on the timer. You should get a reading between 2000 and 3000 OHMs or in the range of the suggested reading on the diagram.
How do I fix my dryer knob?
How do you fix a dryer start switch?
– Shut off the power. Unplug the dryer. …
– Pull the knob off. Pull the control knob straight up and off of the front of the push-to-start switch. …
– Remove the back panel. …
– Remove the push-to-start switch. …
– Install the new push-to-start switch. …
– Reattach the back panel. …
– Reinstall the control knob. …
– Restore power to the dryer.
How do you fix a dryer timer knob?
How do I know if my dryer switch is bad?
When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
How do you fix a GE dryer timer knob?
How do I know if my dryer fuse is blown?
– Unplug your dryer and ensure it is no longer connected to the gas or electric.
– Locate the thermal fuse, as above.
– Disconnect the thermal fuse from the wires.
– Test the fuse with a multimeter.
– If the needle on your multimeter does not move, your thermal fuse is blow.
Don’t forget to share this post 
References and Further Readings :
