If the refrigerator ice maker is not working the water filter might be clogged. Try changing the water filter. … If the ice maker is not working the icemaker mold thermostat might be defective. Inside the control module of the ice maker is a thermostat which monitors the temperature of the ice mold (ice tray).
Thereof, What causes a ice maker to stop working?
Cause: A common cause for a clog is frozen water in the line. … Cause: There is also a possibility that the water filter for the ice maker is clogged. Fix: Locate and replace the water filter. Filters for ice makers are typically located inside the refrigerator (to keep them from freezing).
Also to know is, Where is the reset button on Frigidaire ice maker? The reset button is located on the front of the ice maker, underneath the motor housing, past the front cover. Press and hold the reset button (you’ll need to apply some pressure here) until you hear the ice tray motor begin to torque, then release.
Subsequently, question is, How do you fix a Kenmore refrigerator ice maker? – Check your refrigerator and make sure it’s perfectly level.
– Check your ice maker unit and make sure it’s level.
– Check the water supply line for damage, pinching, or kinks.
– Check the fill cup; make sure it’s aligned correctly with the water funnel.
Also, Why is my Kenmore Elite not making ice?
If the refrigerator ice maker is not working the water filter might be clogged. … If the ice maker is not working the icemaker mold thermostat might be defective. Inside the control module of the ice maker is a thermostat which monitors the temperature of the ice mold (ice tray).
How do I get my Kenmore ice maker to work?
– Check your refrigerator and make sure it’s perfectly level.
– Check your ice maker unit and make sure it’s level.
– Check the water supply line for damage, pinching, or kinks.
– Check the fill cup; make sure it’s aligned correctly with the water funnel.
How do I force my ice maker to cycle?
– Open the freezer door to remove the ice bin from below the ice maker.
– Empty the ice from the bin. …
– Press the ice maker toggle switch to the “On” setting if it is not already activated.
– Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.
How do I stop my ice maker from leaking?
– Be sure the water line fittings are secure.
– Check the water valve for leaks.
– Water could be leaking from the fill tube extension.
– The defrost water drain may be cracked or overflowing. …
– Side-by-Side Refrigerator – Water on Floor, Repairing A Clogged Defrost Drain. …
– Check for water on the exterior of the refrigerator case.
How do I force my Frigidaire ice maker to cycle?
– Open the freezer door to remove the ice bin from below the ice maker.
– Empty the ice from the bin. …
– Press the ice maker toggle switch to the “On” setting if it is not already activated.
– Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.
How do you reset a Frigidaire ice maker?
Some Frigidaire refrigerators have an an on/off button for the icemaker located on the front control panel. To reset the icemaker press this switch until the LED turns red, wait a few minutes, then press and hold it until the LED turns green.
Why did my Frigidaire stopped making ice?
If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do you reset a Frigidaire freezer?
– Unplug Freezer for at least 20 minutes.
– Plug Freezer back in.
– Hold Alarm Reset Button for 3 seconds.
– Quickly, press the DOWN ARROW 3 times.
– Press the UP ARROW 1 time.
– Select Temperature you would like for your freezer.
Why is my Kenmore ice maker leaking water?
The water inlet valve supplies water to the refrigerator ice and water dispenser. … If the water pressure is too low, the valve may not close fully when the power is shut off. As a result, the valve leaks water into the ice maker, causing it to overflow.
How do I remove the ice maker from my Kenmore freezer?
How do I reset my Kenmore Elite ice maker?
Find the on and off switch on the front of the ice maker’s PC board and turn the machine off. Unplug the refrigerator and wait five minutes before plugging it back in. Turn the ice maker back on and return the cover plate.
How do I reset my Kenmore ice maker?
Find the on and off switch on the front of the ice maker’s PC board and turn the machine off. Unplug the refrigerator and wait five minutes before plugging it back in. Turn the ice maker back on and return the cover plate.
Can water filter cause ice maker not to work?
While a clogged water filter could be the cause of your ice maker not working, there are more common causes. First, make sure that your icemaker is simply turned on and plugged in. Check the power cord and make sure it is plugged in. … Check the water supply to make sure it is going from the fridge to your freezer.
Don’t forget to share this post 
References and Further Readings :
